LM35 Temperature Sensor
LM35 Temperature Sensor Specifications:
- Calibrated Directly in Celsius (Centigrade)
- Linear + 10-mV/°C Scale Factor
- 0.5°C Ensured Accuracy (at 25°C)
- Rated for Full −55°C to 150°C Range
- Suitable for Remote Applications
- Low-Cost Due to Wafer-Level Trimming
- Operates from 4 V to 30 V
- Less than 60-µA Current Drain
- Low Self-Heating, 0.08°C in Still Air
- Non-Linearity Only ±¼°C Typical
- Low-Impedance Output, 0.1 Ω for 1-mA Load
₨180
CompareLM35 Temperature Sensor is a precision integrated-circuit temperature device with an output voltage linearly proportional to the Centigrade temperature. The LM35 device has an advantage over linear temperature sensors calibrated in Kelvin, as the user is not required to subtract a large constant voltage from the output to obtain convenient Centigrade scaling.
Lower cost is assured by trimming and calibration at the wafer level. The low-output impedance, linear output, and precise inherent calibration of the LM35 device make interfacing to readout or control circuitry especially easy. The device is used with single power supplies, or with plus and minus supplies. As the LM35 device draws only 60 µA from the supply, it has very low self-heating of less than 0.1°C in still air.
Based on 0 reviews
Be the first to review “LM35 Temperature Sensor”
You must be logged in to post a review.
Related products
-
Sensors
MQ-7 Carbon Monoxide Gas Sensor
MQ7 Gas Sensor Carbon Monoxide Sensor Features:
- Sensitive for carbon monoxide
- Output voltage boosts along with the concentration of the measured gases increases
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
Specifications:
- Power: 2.5V ~ 5.0V
- Dimension: 40.0mm * 21.0mm
- Mounting hole size: 2.0mm
SKU: n/a -
Sensors
DS18B20 Temperature Sensor
DS18B20 Temperature Sensor Key Features
- Unique 1-Wire® Interface Requires Only One Port Pin for Communication
- Reduce Component Count with Integrated Temperature Sensor and EEPROM
- Measures Temperatures from -55°C to +125°C (-67°F to +257°F)
- ±0.5°C Accuracy from -10°C to +85°C
- Programmable Resolution from 9 Bits to 12 Bits
- No External Components Required
- Parasitic Power Mode Requires Only 2 Pins for Operation (DQ and GND)
- Simplifies Distributed Temperature-Sensing Applications with Multidrop Capability
- Each Device Has a Unique 64-bit Serial Code Stored in an On-Board ROM
- Flexible User-Definable Nonvolatile (NV) Alarm Settings with Alarm Search Command Identifies Devices with Temperatures Outside Programmed Limits
- Available in 8-Pin SO (150 mils), 8-Pin µSOP, and 3-Pin TO-92 Packages
SKU: n/a -
Sensors
MQ-3 Alcohol Gas Sensor
MQ3 Alcohol Gas Sensor Specifications and Features:
- Model No.: MQ-3
- Dimensions: 36 x 20 x 21 mm (LxWxH)
- Weight: 6gm
- Heater voltage: 5±0.2V (AC•DC)
- Loop voltage: ≤24V (DC)
- Load resistance: Adjustable
- Heating Resistance: 31Ω±3Ω (Room temperature)
- Heating Power: ≤ 900mW
- Surface thermal resistance: 2Kohm-20Kohm (0.4mg/L alcohol)
- Sensitivity: Rs (in the air)/Rs (0.4mg/L alcohol) ≥ 5
- Working temperature: 20 degrees ±2 degree
- Humidity: 65%±5%RH
- Signal output light indicator.
- Analog and level signal output.
- TTL output valid signal is low. (When the output low signal light can be directly connected microcontroller or relay module).
- The carbon monoxide detection with better sensitivity.
- Has a long service life and reliable stability.
- Rapid response recovery features.
SKU: n/a -
Sensors
MQ-5 LPG Gas Sensor
MQ5 LPG Gas Sensor Features:
- Good sensitivity to Combustible gas in a wide range
- High sensitivity to Methane, Butane and Propane
- Long life and low cost
- Simple drive circuit
Specifications:
- Detection Range: 100 – 10,000 ppm iso-butane propane
- Fast Response Time: <10s
- Heater Voltage: 5.0V
- Dimensions: 18mm Diameter, 17mm High excluding pins, Pins – 6mm High
SKU: n/a
There are no reviews yet.