A44E Hall Effect Sensor AH44E
5000 in stock
A44E Hall Effect Sensor AH44E Features :
- Hall-effect sensor with a digital output.
- Operating voltage ranges from 4.5V to 28V. (typically 5V).
- The output current is 25 milliamps.
- It is possible to utilize a magnet to detect both of its poles.
- The voltage at the output is the same as the voltage at the operating point.
- The operating temperature ranges from -40°C to 85°C.
- The time it takes to turn on and turn off is 2uS each.
- Built-in protection against reverse polarity.
- Suitability for use in automotive and industrial applications
₨25
5000 in stock
CompareThe sensor IC used is AH44E unipolar digital Hall Effect sensor by allegro. The AH44E is a small, versatile linear Hall-effect device that is operated by the magnetic field from a permanent magnet or an electromagnet. The output voltage is set by the supply voltage and varies in proportion to the strength of the magnetic field. The integrated circuitry features low noise output, which makes it unnecessary to use external filtering. It also includes precision resistors to provide increased temperature stability and accuracy. The operating temperaturerange of these linear Hall sensors is -40oC to 85oC, appropriate for commercial, consumer and industrial applications. The sensor has three pins pin1-Vcc, pin2-GND, and pin3-Output.
Related products
-
Sensors
Fire Sensor Module
Fire Sensor Module Features :- High Photo Sensitivity
- Fast Response Time
- Sensitivity adjustable
- Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
- Detection range: up to 100 cm.
- Adjustable detection range.
- Detection angle about 60 degrees, it is sensitive to the flame spectrum.
- Comparator chip LM393 makes module readings stable.
- Operating voltage 3.3V-5V.
- Digital and Analog Output.
- Power indicator and digital switch output indicator.
SKU: n/a -
Sensors
MQ-135 Air Quality Gas Sensor
Specifications of MQ135 Gas Sensor:
- Wide detecting scope
- Fast response and High sensitivity
- Stable and long life Simple drive circuit
- Used in air quality control equipment for buildings/offices, is suitable for detecting
of NH3, NOx, alcohol, Benzene, smoke, CO2, etc. - Size: 35mm x 22mm x 23mm (length x width x height)
- Working voltage: DC 5 V
- Signal output instruction.
- Dual signal output (analog output, and high/low digital output)
- 0 ~ 4.2V analog output voltage, the higher the concentration the higher the voltage.
SKU: n/a -
Sensors
LM35 Waterproof Temperature Sensor
LM35 Waterproof Temperature Sensor Specifications:
- Directly Celsius temperature calibration;
- Linear :+ 10.0mV / ℃;
- Ensure the accuracy : 0.5 ℃ (at + 25 ℃ when);
- Temperature range : 0 ℃ ~ 100 ℃
- Direct output voltage signal;
- Internally precision fine-tuning;
- Wide supply voltage:4 ~ 30V;
- Operating current: Less than 60μA;
- Low self-heating, in still air 0.1 ℃;
- Only non-linear value ± 1/4 ℃ of;
- Low-impedance output, 0.1Ω at 1mA load
SKU: n/a -
Sensors
MQ-3 Alcohol Gas Sensor
MQ3 Alcohol Gas Sensor Specifications and Features:
- Model No.: MQ-3
- Dimensions: 36 x 20 x 21 mm (LxWxH)
- Weight: 6gm
- Heater voltage: 5±0.2V (AC•DC)
- Loop voltage: ≤24V (DC)
- Load resistance: Adjustable
- Heating Resistance: 31Ω±3Ω (Room temperature)
- Heating Power: ≤ 900mW
- Surface thermal resistance: 2Kohm-20Kohm (0.4mg/L alcohol)
- Sensitivity: Rs (in the air)/Rs (0.4mg/L alcohol) ≥ 5
- Working temperature: 20 degrees ±2 degree
- Humidity: 65%±5%RH
- Signal output light indicator.
- Analog and level signal output.
- TTL output valid signal is low. (When the output low signal light can be directly connected microcontroller or relay module).
- The carbon monoxide detection with better sensitivity.
- Has a long service life and reliable stability.
- Rapid response recovery features.
SKU: n/a
