USB to ESP8266 Adapter
USB to ESP8266 Adapter Module Specifications:
- Connector Types: USB-A (Male) to ESP8266-compatible connector
- Compatibility: Works with a wide range of ESP8266 modules
- Data Transfer Rate: Supports high-speed data transfer for efficient programming
- Power Supply: Draws power directly from the USB port, eliminating the need for an external power source
- Dimensions: Compact form factor for easy integration into different projects
- Operating System Support: Compatible with major operating systems, including Windows, macOS, and Linux
₨150
CompareThe USB to ESP8266 Adapter Module is a versatile and compact device designed to facilitate seamless communication between your computer or USB-enabled device and the ESP8266 Wi-Fi module. This adapter serves as a bridge, enabling a straightforward interface between your computer’s USB port and the ESP8266 module, unlocking a myriad of possibilities for IoT (Internet of Things) and wireless connectivity projects.
The USB to ESP8266 Adapter Module is a versatile and compact device designed to facilitate seamless communication between your computer or USB-enabled device and the ESP8266 Wi-Fi module. This adapter serves as a bridge, enabling a straightforward interface between your computer’s USB port and the ESP8266 module, unlocking a myriad of possibilities for IoT (Internet of Things) and wireless connectivity projects.
Based on 0 reviews
Be the first to review “USB to ESP8266 Adapter”
You must be logged in to post a review.
Related products
-
Modules and Motors
L6203 Motor Driver Dual Full Bridge
L6203 Motor Driver Features
- SUPPLY VOLTAGE UP TO 48V
- 5A MAX PEAK CURRENT (2A max. for L6201)
- TOTAL RMS CURRENT UP TO:4A
- RDS (ON) 0.3 Ω (typical value at 25 °C)
- CROSS CONDUCTION PROTECTION
- TTL COMPATIBLE DRIVE
- OPERATING FREQUENCY UP TO 100 KHz
- THERMAL SHUTDOWN
- INTERNAL LOGIC SUPPLY
- HIGH EFFICIENCY
SKU: n/a -
-
Modules and Motors
MG996R Servo Motor
MG996R Servo Motor Specifications:
- Weight: 55 g
- Dimensions: Approximately 40.7 x 19.7 x 42.9 mm
- Stall Torque: 9.4 kgf·cm (4.8 V), 11 kgf·cm (6 V)
- Operating Speed: 60° / 0.17s at 4.8V, 60° / 0.14s at 6V
- Operating Voltage: 4.8V – 7.2V
- Current: 500 mA
- Idle Current: 2.5 A (6V)
- Deadband Width: 5 µs
- Stable and shock-resistant dual ball bearing design
- Temperature Range: 0°C – 55°C
SKU: n/a -
Modules and Motors
RC522 RFID Card Reader
RC522 RFID Card Reader Features and Benefits
- Highly integrated analog circuitry to demodulate and decode responses
- Buffered output drivers for connecting an antenna with the minimum number of external components
- Supports ISO/IEC 14443 A/MIFARE and NTAG
- The typical operating distance in Read/Write mode is up to 50 mm depending on the antenna size and tuning
- Supports MF1xxS20, MF1xxS70 and MF1xxS50 encryption in Read/Write mode
- Supports ISO/IEC 14443 A higher transfer speed communication up to 848 kBd
- Supports MFIN/MFOUT
- Additional internal power supply to the smart card IC connected via MFIN/MFOUT
- Supported host interfaces
- SPI up to 10 Mbit/s
- I 2C-bus interface up to 400 kBd in Fast mode, up to 3400 kBd in High-speed mode
- RS232 Serial UART up to 1228.8 kBd, with voltage levels dependent on the pin voltage supply
- FIFO buffer handles 64-byte send-and-receive
- Flexible interrupt modes
- Hard reset with low power function
- Power-down by software mode
- Programmable timer
- Internal oscillator for connection to 27.12 MHz quartz crystal
- 2.5 V to 3.3 V power supply
- CRC coprocessor
- Programmable I/O pins
- Internal self-test
SKU: n/a
There are no reviews yet.