150W Boost Converter DC-DC 10-32V to 12-35V Step Up
- Size: 10-32V to 12-35V
- Module Properties: non-isolated step-up module (BOOST)
- 65 * 56.5 * 23 (length * width * high) (mm)
- Input voltage:10-32V
- Output voltage: 12-35V (adjustable)
- Output Current: 6A (MAX) Input Current: 10A (MAX) (Please enhance heat dissipation if more than 10A)
- Output power: natural cooling 100W (MAX), enhanced heat dissipation 150W (MAX)
- Easy to drive 65W 90W dual-core notebook.
- Use a 12V battery drive 19V 3.42A notebook, the module temperature about 45¡ãc
- Conversion efficiency: 94% (measured at Input 16V, output 19V 2.5A)
- Output Ripple: 2% (MAX) 20M-bandwidth
- Operating Temperature: Industrial (-40¡ãc to +85¡ãc) (ambient temperature exceeds 40¡ãc, lower power use, or to enhance heat dissipation)
- Full load temperature rise: 45¡ãc
- No-load current: 25mA typical
- Voltage regulation: ¡À 0.5%
- Dynamic response speed: 5% 200uS
- Short circuit protection: None (Please Install fuses and protection circuits at the Input port.)
₨600
Compare150W Boost Converter DC-DC 10-32V to 12-35V Step Up
The 150W Boost Converter DC-DC 10-32V to 12-35V Step Up package includes a power Boost Module 150W. This module allows you to step up an input voltage as low as 10V and set the output to 12V-35V. The output voltage will be higher than the input voltage.
The boost converter design is based on the popular Texas Instrument’s UC3844 current mode PWM controller chip.
Applications:
DIY an adjustable on-board power supply, you just input DC 12V, then you can get output DC 12V-35V (adjustable), But the output voltage can not below the input voltage.
DIY a booster charger.
Provide power for your electronic equipment.
Use Solar battery charging for the electric accumulator.
Some Applications:
1. DIY an output adjustable vehicle power supply, connect the 12V input, and the output could be 14-35V(adjustable freely), However, the output voltage can not be less than the input voltage.
2. Car laptop power supply: connected to 12V power supply, output voltage regulation as your notebook needs.
Based on 0 reviews
Be the first to review “150W Boost Converter DC-DC 10-32V to 12-35V Step Up”
You must be logged in to post a review.
Related products
-
Modules and Motors
MG996R Servo Motor
MG996R Servo Motor Specifications:
- Weight: 55 g
- Dimensions: Approximately 40.7 x 19.7 x 42.9 mm
- Stall Torque: 9.4 kgf·cm (4.8 V), 11 kgf·cm (6 V)
- Operating Speed: 60° / 0.17s at 4.8V, 60° / 0.14s at 6V
- Operating Voltage: 4.8V – 7.2V
- Current: 500 mA
- Idle Current: 2.5 A (6V)
- Deadband Width: 5 µs
- Stable and shock-resistant dual ball bearing design
- Temperature Range: 0°C – 55°C
SKU: n/a -
-
-
Modules and Motors
MG946R Servo Motor
MG946R Servo Motor Features:Â
- Power: 4.8V – 6V DC max (5V works well)
- Average Speed: 60 degrees in 0.20 sec (@ 4.8V), 60 degrees in 0.16 sec (@ 6.0V)
- Weight: 62.41g
- Torque: At 4.8V: 8.5 kg-cm / 120 oz-in, and at 6V: 10 kg-cm / 140 oz-in.
- Size mm: (L x W x H) 40.7 x 19.7 x 42.9
SKU: n/a
There are no reviews yet.