Modules and Motors
Micro SD Card Shield
Micro SD Card Shield Specifications
- Interfaces: SPI
- Length x Width: 25mm x 28mm
-
Operating Voltage: 3.3V
-
Storage Maximum Capacity: when Micro SD card in FAT16 Mode – 2GB Maximum Capacity when Micro SD card in FAT32 Mode – 32GB
₨150
CompareThis Micro SD Card Shield is designed for use with the WeMos D1 mini and mini Pro development boards. The shield provides a means of allowing a WeMos D1 mini to directly communicate with most types of microSD cards. The shield is also compatible with the standard Arduino SD card library.
This shield is designed for use with the Wemos/Lolin D1 mini and mini Pro development boards (see item HCWEMO0002). The shield provides a means of allowing a Wemos/Lolin D1 mini to directly communicate with most types of microSD card. it is also compatible with the standard Arduino SD card library. Supplied with two sets of pins headers for stacking onto a D1 Mini.
Based on 0 reviews
Be the first to review “Micro SD Card Shield”
You must be logged in to post a review.
Related products
-
Modules and Motors
ESP-01 ESP8266 WiFi Module
ESP 01 WiFi Module ESP8266 Features
- 802.11 b/g/n protocol
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, and power management units
- +19.5dBm output power in 802.11b mode
- Integrated temperature sensor
- Supports antenna diversity
- Power down leakage current of < 10uA
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4s guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
SKU: ESP-01-ESP8266-WiFi-Module -
Modules and Motors
MG996R Servo Motor
MG996R Servo Motor Specifications:
- Weight: 55 g
- Dimensions: Approximately 40.7 x 19.7 x 42.9 mm
- Stall Torque: 9.4 kgf·cm (4.8 V), 11 kgf·cm (6 V)
- Operating Speed: 60° / 0.17s at 4.8V, 60° / 0.14s at 6V
- Operating Voltage: 4.8V – 7.2V
- Current: 500 mA
- Idle Current: 2.5 A (6V)
- Deadband Width: 5 µs
- Stable and shock-resistant dual ball bearing design
- Temperature Range: 0°C – 55°C
SKU: n/a -
-
Modules and Motors
L297 & L298 Stepper Motor Driver
L297 L298 Stepper Motor Driver Features
- Easily adjustable motor current (0 to 2A)
- Full and Half stepping modes
- Step, Direction and Enable inputs (5V logic level)
- Synchroniseable when using multiple drivers
- Enable input can be connected to ground to disable the motor
SKU: n/a -
Modules and Motors
RC522 RFID Card Reader
RC522 RFID Card Reader Features and Benefits
- Highly integrated analog circuitry to demodulate and decode responses
- Buffered output drivers for connecting an antenna with the minimum number of external components
- Supports ISO/IEC 14443 A/MIFARE and NTAG
- The typical operating distance in Read/Write mode is up to 50 mm depending on the antenna size and tuning
- Supports MF1xxS20, MF1xxS70 and MF1xxS50 encryption in Read/Write mode
- Supports ISO/IEC 14443 A higher transfer speed communication up to 848 kBd
- Supports MFIN/MFOUT
- Additional internal power supply to the smart card IC connected via MFIN/MFOUT
- Supported host interfaces
- SPI up to 10 Mbit/s
- I 2C-bus interface up to 400 kBd in Fast mode, up to 3400 kBd in High-speed mode
- RS232 Serial UART up to 1228.8 kBd, with voltage levels dependent on the pin voltage supply
- FIFO buffer handles 64-byte send-and-receive
- Flexible interrupt modes
- Hard reset with low power function
- Power-down by software mode
- Programmable timer
- Internal oscillator for connection to 27.12 MHz quartz crystal
- 2.5 V to 3.3 V power supply
- CRC coprocessor
- Programmable I/O pins
- Internal self-test
SKU: n/a
There are no reviews yet.