Modules and Motors
TDA7492 Wireless Bluetooth Receiver Digital Audio Amplifier Board 50W 50W
Availability:
Out of stock
Specifications:
- Amplifier Chip: TDA7492 Class D
- Output Power: 50W+50W (Stereo)
- Bluetooth Version: 4.0
- Input Voltage: DC 8-25V
- Input Impedance: 470 ohms
- SNR (Signal-to-Noise Ratio): 80dB
- Frequency Response: 20Hz – 20kHz
- Efficiency: 90%
- Dimensions: [Insert Dimensions Here]
- Weight: [Insert Weight Here]
- Input Connector: Bluetooth, 3.5mm Audio Jack
- Protection Features: Overcurrent, Overtemperature, Short-Circuit
₨1,150
Out of stock
CompareThe TDA7492 50W+50W Wireless Bluetooth 4.0 Receiver Digital Audio Amplifier Board is a compact and versatile audio solution designed for amplifying digital audio signals wirelessly. This amplifier board integrates advanced Bluetooth 4.0 technology, allowing seamless connectivity with various audio sources such as smartphones, tablets, and laptops. With its robust build and powerful amplification capabilities, this board is perfect for DIY audio projects, home audio systems, and small-scale audio applications.
Based on 0 reviews
Be the first to review “TDA7492 Wireless Bluetooth Receiver Digital Audio Amplifier Board 50W 50W”
You must be logged in to post a review.
Related products
-
-
Modules and Motors
ESP-01 ESP8266 WiFi Module
ESP 01 WiFi Module ESP8266 Features
- 802.11 b/g/n protocol
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, and power management units
- +19.5dBm output power in 802.11b mode
- Integrated temperature sensor
- Supports antenna diversity
- Power down leakage current of < 10uA
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4s guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
SKU: ESP-01-ESP8266-WiFi-Module -
Modules and Motors
RC522 RFID Card Reader
RC522 RFID Card Reader Features and Benefits
- Highly integrated analog circuitry to demodulate and decode responses
- Buffered output drivers for connecting an antenna with the minimum number of external components
- Supports ISO/IEC 14443 A/MIFARE and NTAG
- The typical operating distance in Read/Write mode is up to 50 mm depending on the antenna size and tuning
- Supports MF1xxS20, MF1xxS70 and MF1xxS50 encryption in Read/Write mode
- Supports ISO/IEC 14443 A higher transfer speed communication up to 848 kBd
- Supports MFIN/MFOUT
- Additional internal power supply to the smart card IC connected via MFIN/MFOUT
- Supported host interfaces
- SPI up to 10 Mbit/s
- I 2C-bus interface up to 400 kBd in Fast mode, up to 3400 kBd in High-speed mode
- RS232 Serial UART up to 1228.8 kBd, with voltage levels dependent on the pin voltage supply
- FIFO buffer handles 64-byte send-and-receive
- Flexible interrupt modes
- Hard reset with low power function
- Power-down by software mode
- Programmable timer
- Internal oscillator for connection to 27.12 MHz quartz crystal
- 2.5 V to 3.3 V power supply
- CRC coprocessor
- Programmable I/O pins
- Internal self-test
SKU: n/a -
-
There are no reviews yet.