Modules and Motors
HM-10 Bluetooth Module CC2451
HM10 Bluetooth Module Specifications:
- Bluetooth 4.0 module compliant with ISM 2.4 GHz (HM-10)
- Uses Texas Instruments CC2541 SoC chip with 256K Flash memory and 8K RAM
- Supports master and slave modes
- RX standard gain: 19.6 mA
- TX -6 dBm: 24 mA
- Frequency: 2402 – 2483.5 MHz in 20 kHz steps
- Modulation and Data Rate: 1 Mbps, GFSK
- Number of channels: 40
- Output power: -23 to 4 dBm
- Reception sensitivity: -93dBm/-87dBm
- Stack: ATT, GATT, SMP, L2CAP, GAP
- Range: over 70 meters 10-bit ADC
- Serial interface: UART/SPI Wake-up interrupt, Watchdog Timer
- AES Security Coprocessor
- Power supply: ranges between 2V and 3.6V
- VDD ripple: 100mV max
- Current consumption (at 25°C with VDD = 3V):
– Power Mode 3 (External Interrupts): 0.4uA
–Â Power Mode 2 (SleepTimerOn): 0.9uA
– Power Mode 1 (3-μs Wake-Up): 235uA
–Â RX Standard Gain: 19.6mA
– TX -6 dBm: 24mA
– TX 0 dBm: – - Operating temperature: -40°C to +85°C
- Dimensions (mm): 27x13x1.6
- Weight: 5 grams.
₨750
CompareHM10 Bluetooth Module is a Bluetooth 4.0 (Low Energy) module compliant with ISM 2.4 GHz, with master/slave mode of operation and transparent data transmission, based on the Texas Instruments CC2541 chip with 256K Flash memory and 8K RAM.
It can be controlled through simple AT commands (via UART) or programmed with custom applications. Ideal for use in projects where a Bluetooth connection is needed, such as between a microcontroller and a PC. The power supply ranges between 2V and 3.6V DC.
Based on 0 reviews
Be the first to review “HM-10 Bluetooth Module CC2451”
You must be logged in to post a review.
Related products
-
Modules and Motors
MG946R Servo Motor
MG946R Servo Motor Features:Â
- Power: 4.8V – 6V DC max (5V works well)
- Average Speed: 60 degrees in 0.20 sec (@ 4.8V), 60 degrees in 0.16 sec (@ 6.0V)
- Weight: 62.41g
- Torque: At 4.8V: 8.5 kg-cm / 120 oz-in, and at 6V: 10 kg-cm / 140 oz-in.
- Size mm: (L x W x H) 40.7 x 19.7 x 42.9
SKU: n/a -
-
Modules and Motors
RC522 RFID Card Reader
RC522 RFID Card Reader Features and Benefits
- Highly integrated analog circuitry to demodulate and decode responses
- Buffered output drivers for connecting an antenna with the minimum number of external components
- Supports ISO/IEC 14443 A/MIFARE and NTAG
- The typical operating distance in Read/Write mode is up to 50 mm depending on the antenna size and tuning
- Supports MF1xxS20, MF1xxS70 and MF1xxS50 encryption in Read/Write mode
- Supports ISO/IEC 14443 A higher transfer speed communication up to 848 kBd
- Supports MFIN/MFOUT
- Additional internal power supply to the smart card IC connected via MFIN/MFOUT
- Supported host interfaces
- SPI up to 10 Mbit/s
- I 2C-bus interface up to 400 kBd in Fast mode, up to 3400 kBd in High-speed mode
- RS232 Serial UART up to 1228.8 kBd, with voltage levels dependent on the pin voltage supply
- FIFO buffer handles 64-byte send-and-receive
- Flexible interrupt modes
- Hard reset with low power function
- Power-down by software mode
- Programmable timer
- Internal oscillator for connection to 27.12 MHz quartz crystal
- 2.5 V to 3.3 V power supply
- CRC coprocessor
- Programmable I/O pins
- Internal self-test
SKU: n/a -
Modules and Motors
RFID Card 13.56MHz
RFID Card 13.56MHz Specifications:
- Frequency: 13.56MHz
- Communication Protocol: ISO 14443A/B, ISO 15693
- Chip Type: Contactless Smart Card IC (Integrated Circuit)
- Memory Capacity: Varies based on chip type and application requirements (e.g., 1KB, 4KB, or more)
- Operating Range: Standard reading distance up to 10 cm, depending on the RFID reader’s power and antenna design.
- Material: PVC or other durable materials
- Dimensions: Standard credit card size (85.6 x 53.98 mm) or customizable based on specific requirements.
- Operating Temperature: -20°C to +70°C
- Data Encryption: Advanced encryption algorithms for enhanced security
- Compatibility: Compatible with a wide range of RFID readers and devices supporting the 13.56MHz frequency.
SKU: n/a -
Modules and Motors
ACS712 Arduino Current Sensor
ACS712 Arduino Current Sensor Voltage Output
- 1/2 VCC when no load or it is 2.5V since we use 5V as VCC.
- 5A type generate 185mV every amp current
- 20A type generate 100mV every amp current
- 30A type generate 66mV every amp current
SKU: acs712-current-sensor
There are no reviews yet.