YF-S201 Water Flow Measurement Sensor
 YF S201 Water Flow Measurement Sensor Specifications
- Operating Voltage: 4.5V to 18V DC
- Output type: 5V TTL
- Maximum current draw: 15mA at 5V
- The sensor used: Hall Effect
- Working Flow rate: 1 to 30 Liters/Minute
- Accuracy: ±10%
- Pulses per Liter: 450
- Output duty cycle: 50% +-10%
- Maximum water pressure: 2.0 MPa
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
₨600
CompareYF S201 water sensor with high-grade quality sealing property. It works on the Hall effect principle and with a flow rate range of 1~30L/min. The module has three pins: Power, Ground, and Analog output. YF-S201 consumes very little current and can work with an allowing pressure of ≤1.75MPa
YF S201 water sensor with high-grade quality sealing property. It works on the Hall effect principle and with a flow rate range of 1~30L/min. The module has three pins: Power, Ground, and Analog output. YF-S201 consumes very little current and can work with an allowing pressure of ≤1.75MPa
YF S201 water flow measurement sensor with high-grade quality sealing property. It works on the Hall effect principle and with a flow rate range of 1~30L/min. The module has three pins: Power, Ground, and Analog output. YF-S201 consumes very little current and can work with an allowing pressure of ≤1.75MPa
Based on 0 reviews
Be the first to review “YF-S201 Water Flow Measurement Sensor”
You must be logged in to post a review.
Related products
-
Sensors, Arduino, Modules and Motors
Arduino KY-032 Obstacle Avoidance Sensor Module
Arduino KY 032 Sensor Module Specifications:
- Operating Voltage: 3.3V to 5V
- Detection Range: Adjustable, typically 2cm to 30cm
- Operating Current: <25mA
- Output Type:
- Digital Output (D0): High/Low signal indicating obstacle presence
- Analog Output (A0): Voltage proportional to the distance from the obstacle
- Indicator: Built-in status LED
- Dimensions: 30mm x 14mm x 8mm (L x W x H)
- Mounting Holes: Yes, for convenient installation
- Interface: 3-pin header for easy connection to Arduino
- Material: Quality materials for durability and reliability in various environments.
Â
SKU: n/a -
Arduino, Modules and Motors
ZMCT103C 5A AC Current Transformer Module
ZMCT103C 5A AC Current Transformer Module Specifications:
- On-board precision micro-current transformer
- On-board high-precision op-amp circuit, to do accurate sampling and appropriate compensation and other functions to signal
- The module can measure AC within 5A, corresponding output analog can be adjusted
- Under ideal conditions, the input voltage VCC is 3-35V, according to the potentiometer (adjust the amplification ratio, amplification range 0-100 times) to adjust the required output voltage, but the output (OUT) of the maximum voltage does not exceed 1 / 2 VCC.
- The output signal is the AC voltage signal, and the output signal voltage does not exceed the maximum 1 / 2VCC.
- PCB board size: 38 (mm) x 18.5 (mm)
SKU: n/a -
Modules and Motors, Arduino
ZMPT101B 250V AC Voltage Sensor Module For Arduino
Specifications:
- Measure within 250V AC
- Onboard micro-precision voltage transformer
- Analog output corresponding quantity can be adjusted.
- Good consistency, for voltage and power measurement
- Very efficient and accuracy
SKU: n/a -
Sensors
Fire Sensor Module
Fire Sensor Module Features :- High Photo Sensitivity
- Fast Response Time
- Sensitivity adjustable
- Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
- Detection range: up to 100 cm.
- Adjustable detection range.
- Detection angle about 60 degrees, it is sensitive to the flame spectrum.
- Comparator chip LM393 makes module readings stable.
- Operating voltage 3.3V-5V.
- Digital and Analog Output.
- Power indicator and digital switch output indicator.
SKU: n/a
There are no reviews yet.