LCDs
2.4 Inch TFT LCD For Arduino
2.4 Inch TFT LCD Arduino Specifications:
- 2.4″ diagonal LCD TFT display
- 240×320 resolution
- 5V compatible! Use with 3.3V or 5V logic
- Onboard 3.3V 300mA LDO regulator
- 8-bit digital interface, plus 4 control lines
- 4-wire resistive touchscreen
- Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, and 3 and analog 4 and 5. Pin 12 is available if not using the microSD
₨2,200
CompareThe 2.4-inch TFT LCD Arduino is a compact and versatile display module designed for use with Arduino boards. This high-resolution color screen provides a vibrant and clear interface, making it ideal for various DIY electronics projects, educational purposes, and prototyping applications. With easy compatibility and a user-friendly interface, this TFT LCD enhances the visual experience of your Arduino projects.
Related products
-
Arduino
Arduino Uno R3
Arduino Uno R3 board Specifications:
- It is an ATmega328P based Microcontroller
- The Operating Voltage of the Arduino is 5V
- The recommended input voltage ranges from 7V to 12V
- The i/p voltage (limit) is 6V to 20V
- Digital input and output pins 14
- Digital input & output pins (PWM)-6
- Analog i/p pins are 6
- DC Current for each I/O Pin is 20 mA
- DC Current used for 3.3V Pin is 50 mA
- Flash Memory -32 KB, and 0.5 KB memory is used by the boot loader
- SRAM is 2 KB
- EEPROM is 1 KB
- The speed of the CLK is 16 MHz
- In Built LED
- The length and width of the Arduino are 68.6 mm X 53.4 mm
- The weight of the Arduino board is 25 g
SKU: n/a -
Arduino, Modules and Motors
ZMCT103C 5A AC Current Transformer Module
ZMCT103C 5A AC Current Transformer Module Specifications:
- On-board precision micro-current transformer
- On-board high-precision op-amp circuit, to do accurate sampling and appropriate compensation and other functions to signal
- The module can measure AC within 5A, corresponding output analog can be adjusted
- Under ideal conditions, the input voltage VCC is 3-35V, according to the potentiometer (adjust the amplification ratio, amplification range 0-100 times) to adjust the required output voltage, but the output (OUT) of the maximum voltage does not exceed 1 / 2 VCC.
- The output signal is the AC voltage signal, and the output signal voltage does not exceed the maximum 1 / 2VCC.
- PCB board size: 38 (mm) x 18.5 (mm)
SKU: n/a -
Modules and Motors, Arduino, Raspberry Pi
TM1637 LED Display Module Tube For Arduino Raspberry PI
TM1637 LED Display Module Specifications:
- Using CMOS technology
- Display mode (6-Digit 8 Segment), support a total of positive digital tube output
- Key scan (8X2bit), enhanced anti-jamming key recognition circuit
- Gray scale adjustment circuit (duty cycle 8 adjustable)
- Two-wire serial interface (CLK, DIO)
SKU: n/a -
Zigbee Boards
XBEE Module Zigbee (S1/S2)
XBEE Module Features & Specifications:
- Indoor Range up to 100 ft. (30 m) & Outdoor RF line-of-sight Range up to 300 ft. (100 m)
- Interface: Serial(UART) at 1200-115200 bps
- Supply Voltage: 2.8 – 3.4 V
- Transmit Current (typical) 45mA (@ 3.3 V)
- Idle / Receive Current (typical) 50mA (@ 3.3 V)
- Operating Frequency: ISM 2.4 GHz
- Antenna: Whip antenna
- Supported Network Topologies: Point-to-point, Point-to-multipoint & Peer-to-peer
- Number of Channels: (software selectable) 16 Direct Sequence Channels
- Addressing Options: PAN ID, Channel and Addresses
- ADC and I/O line support
- AT and API Command Modes for configuring module parameters
- Extensive command set
- Small form factor
SKU: n/a - Indoor Range up to 100 ft. (30 m) & Outdoor RF line-of-sight Range up to 300 ft. (100 m)
There are no reviews yet.