Modules and Motors
EM-18 RFID Reader Module
EM 18 RFID Reader Module Specifications:
- Operating frequency: 125kHz
- Operating voltage: DC 5V
- Supply current: <50mA
- Read distance: up to 100mm (depending on the tag used)
- Interface: UART (TTL level)
- Dimensions: 40mm x 40mm x 16mm
- Communication protocol: UART
- Baud rate: 9600, 8, N, 1
₨1,900
CompareEM 18 RFID Reader Module is an RFID reader which is used to read RFID tags of frequency 125 kHz.
After reading tags, it transmits unique ID serially to the PC or microcontroller using UART communication or Wiegand format on respective pins.
EM18 RFID reader reads the data from RFID tags which contain a stored ID which is of 12 bytes.
EM18 RFID reader doesn’t require line-of-sight. Also, it has a short identification range i.e. in a few centimetres.
Based on 0 reviews
Be the first to review “EM-18 RFID Reader Module”
You must be logged in to post a review.
Related products
-
Modules and Motors
ESP-01 ESP8266 WiFi Module
ESP 01 WiFi Module ESP8266 Features
- 802.11 b/g/n protocol
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, and power management units
- +19.5dBm output power in 802.11b mode
- Integrated temperature sensor
- Supports antenna diversity
- Power down leakage current of < 10uA
- Integrated low power 32-bit CPU could be used as application processor
- SDIO 2.0, SPI, UART
- STBC, 1×1 MIMO, 2×1 MIMO
- A-MPDU & A-MSDU aggregation & 0.4s guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
SKU: ESP-01-ESP8266-WiFi-Module -
-
Modules and Motors
MG996R Servo Motor
MG996R Servo Motor Specifications:
- Weight: 55 g
- Dimensions: Approximately 40.7 x 19.7 x 42.9 mm
- Stall Torque: 9.4 kgf·cm (4.8 V), 11 kgf·cm (6 V)
- Operating Speed: 60° / 0.17s at 4.8V, 60° / 0.14s at 6V
- Operating Voltage: 4.8V – 7.2V
- Current: 500 mA
- Idle Current: 2.5 A (6V)
- Deadband Width: 5 µs
- Stable and shock-resistant dual ball bearing design
- Temperature Range: 0°C – 55°C
SKU: n/a -
Modules and Motors
ACS712 Arduino Current Sensor
ACS712 Arduino Current Sensor Voltage Output
- 1/2 VCC when no load or it is 2.5V since we use 5V as VCC.
- 5A type generate 185mV every amp current
- 20A type generate 100mV every amp current
- 30A type generate 66mV every amp current
SKU: acs712-current-sensor -
Modules and Motors
L298N Motor Driver H-Bridge
Features & Specifications
- Driver Model: L298N 2A
- Driver Chip: Double H Bridge L298N
- Motor Supply Voltage (Maximum): 46V
- Motor Supply Current (Maximum): 2A
- Logic Voltage: 5V
- Driver Voltage: 5-35V
- Driver Current:2A
- Logical Current:0-36mA
- Maximum Power (W): 25W
- Current Sense for each motor
- Heatsink for better performance
- Power-On LED indicator
SKU: n/a
There are no reviews yet.