NodeMCU ESP8266 V3 Board
NodeMCU ESP8266 V3 Board Specifications & Features
- Microcontroller: Tensilica 32-bit RISC CPU Xtensa LX106
- Operating Voltage: 3.3V
- Input Voltage: 7-12V
- Digital I/O Pins (DIO): 16
- Analog Input Pins (ADC): 1
- UARTs: 1
- SPIs: 1
- I2Cs: 1
- Flash Memory: 4 MB
- SRAM: 64 KB
- Clock Speed: 80 MHz
- USB-TTL based on CP2102 is included onboard, Enabling Plug n Play
- PCB Antenna
- Small Sized module to fit smartly inside your IoT projects
₨550
CompareNodeMCU ESP8266 V3 Board is an LUA based interactive firmware for Expressif ESP8622 Wi-Fi SoC, as well as an open source hardware board that, unlike the $3 ESP8266 Wi-Fi modules, includes a CP2102 TTL to USB chip for programming and debugging, is breadboard-friendly, and can simply be powered via its micro USB port.
This module is one of the cheapest available wifi-modules in market. V3 or Version3 is the latest version of this module. This tutorial however will facilitate you to connect all the versions of ESP8266 NodeMcu, i.e V1 , V2 or V3.
For makers, having ESP-12 module, rest assured, 12E is no different from its precursor. The only difference : 6 extra GPIOs are present in ESP-12E
Based on 0 reviews
Be the first to review “NodeMCU ESP8266 V3 Board”
You must be logged in to post a review.
Related products
-
Modules and Motors
RC522 RFID Card Reader
RC522 RFID Card Reader Features and Benefits
- Highly integrated analog circuitry to demodulate and decode responses
- Buffered output drivers for connecting an antenna with the minimum number of external components
- Supports ISO/IEC 14443 A/MIFARE and NTAG
- The typical operating distance in Read/Write mode is up to 50 mm depending on the antenna size and tuning
- Supports MF1xxS20, MF1xxS70 and MF1xxS50 encryption in Read/Write mode
- Supports ISO/IEC 14443 A higher transfer speed communication up to 848 kBd
- Supports MFIN/MFOUT
- Additional internal power supply to the smart card IC connected via MFIN/MFOUT
- Supported host interfaces
- SPI up to 10 Mbit/s
- I 2C-bus interface up to 400 kBd in Fast mode, up to 3400 kBd in High-speed mode
- RS232 Serial UART up to 1228.8 kBd, with voltage levels dependent on the pin voltage supply
- FIFO buffer handles 64-byte send-and-receive
- Flexible interrupt modes
- Hard reset with low power function
- Power-down by software mode
- Programmable timer
- Internal oscillator for connection to 27.12 MHz quartz crystal
- 2.5 V to 3.3 V power supply
- CRC coprocessor
- Programmable I/O pins
- Internal self-test
SKU: n/a -
Modules and Motors
RFID Card 13.56MHz
RFID Card 13.56MHz Specifications:
- Frequency: 13.56MHz
- Communication Protocol: ISO 14443A/B, ISO 15693
- Chip Type: Contactless Smart Card IC (Integrated Circuit)
- Memory Capacity: Varies based on chip type and application requirements (e.g., 1KB, 4KB, or more)
- Operating Range: Standard reading distance up to 10 cm, depending on the RFID reader’s power and antenna design.
- Material: PVC or other durable materials
- Dimensions: Standard credit card size (85.6 x 53.98 mm) or customizable based on specific requirements.
- Operating Temperature: -20°C to +70°C
- Data Encryption: Advanced encryption algorithms for enhanced security
- Compatibility: Compatible with a wide range of RFID readers and devices supporting the 13.56MHz frequency.
SKU: n/a -
Modules and Motors
HC06 HC09 Bluetooth Module
HC06 HC09 Bluetooth Module firmware are the modules which are factory set to be Master or Slave modules. Master and slave mode cannot be switched from the factory setting. HC-04 is an industrial grade product, HC-06 is a commercial grade product.
The modules with the HC-09 firmware are replacements for the HC-06 and HC-07 modules.
SKU: n/a -
-
Modules and Motors
MG996R Servo Motor
MG996R Servo Motor Specifications:
- Weight: 55 g
- Dimensions: Approximately 40.7 x 19.7 x 42.9 mm
- Stall Torque: 9.4 kgf·cm (4.8 V), 11 kgf·cm (6 V)
- Operating Speed: 60° / 0.17s at 4.8V, 60° / 0.14s at 6V
- Operating Voltage: 4.8V – 7.2V
- Current: 500 mA
- Idle Current: 2.5 A (6V)
- Deadband Width: 5 µs
- Stable and shock-resistant dual ball bearing design
- Temperature Range: 0°C – 55°C
SKU: n/a
There are no reviews yet.