LCDs
2.4 Inch TFT LCD For Arduino
2.4 Inch TFT LCD Arduino Specifications:
- 2.4″ diagonal LCD TFT display
- 240×320 resolution
- 5V compatible! Use with 3.3V or 5V logic
- Onboard 3.3V 300mA LDO regulator
- 8-bit digital interface, plus 4 control lines
- 4-wire resistive touchscreen
- Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, and 3 and analog 4 and 5. Pin 12 is available if not using the microSD
₨2,200
CompareThe 2.4-inch TFT LCD Arduino is a compact and versatile display module designed for use with Arduino boards. This high-resolution color screen provides a vibrant and clear interface, making it ideal for various DIY electronics projects, educational purposes, and prototyping applications. With easy compatibility and a user-friendly interface, this TFT LCD enhances the visual experience of your Arduino projects.
Related products
-
Arduino
Arduino TFT Display 3.2 Inch LCD
Arduino TFT Display 3.2 Inch LCD Features:
- Support Arduino Mega2560 Directly inserted
- With a Full-angle IPS TFT panel
- OnBorad level conversion chip for 5V/3.3V MCU
- Compatible with 3.3/5 V operation voltage level
- Compatible with Arduino-Series Development Board.
- (Please notice: This Screen is not a touch screen)
- Provided 12-examples with Arduino,3-examples with STM32
- With an SD Card Socket
- With SPI FLASH circuit
Specifications:
- Driver IC: ILI9481
- Screen Size: 3.2 inch
- Display Size : 67.68(W) * 45.12(L) (mm)
- Backlight Type: Highlighting White 6 LED
- Screen Resolution: 480 * 320 Pixel (HVGA)
- Power Consumption : 80~110(mA)
- Screen Type: TFT (IPS Whole Perspective)
- Power : 5V / 3.3V
- Touch Function: None
- Data Bus: 16 Channels Parallel Bus
- Module Interface : 36Pin (Compatible with Arduino Mega2560)
- Size : 89.92(W) * 54.25(L) (mm)
SKU: n/a -
Sensors, Arduino, Modules and Motors
801S Vibration Shock Sensor For Arduino
801S Vibration Shock Sensor For Arduino Specifications:
- Operating Voltage: 3.3V – 5V DC
- Current Consumption: <1mA
- Output Type:
- Digital Output: High/Low (TTL)
- Analog Output: 0V to Vcc (0 – 5V)
- Detection Range: Adjustable via sensitivity potentiometer
- Frequency Response: 10Hz – 10kHz
- Dimensions: 32mm x 14mm x 7mm
- Mounting Holes: Two mounting holes for easy integration into various projects.
- Operating Temperature: -10°C to +70°C
- Interface: 3-pin interface (VCC, GND, Signal)
- Compatibility: Compatible with Arduino and other microcontrollers with digital and analog input capabilities.
SKU: n/a -
Arduino, Modules and Motors
ZMCT103C 5A AC Current Transformer Module
ZMCT103C 5A AC Current Transformer Module Specifications:
- On-board precision micro-current transformer
- On-board high-precision op-amp circuit, to do accurate sampling and appropriate compensation and other functions to signal
- The module can measure AC within 5A, corresponding output analog can be adjusted
- Under ideal conditions, the input voltage VCC is 3-35V, according to the potentiometer (adjust the amplification ratio, amplification range 0-100 times) to adjust the required output voltage, but the output (OUT) of the maximum voltage does not exceed 1 / 2 VCC.
- The output signal is the AC voltage signal, and the output signal voltage does not exceed the maximum 1 / 2VCC.
- PCB board size: 38 (mm) x 18.5 (mm)
SKU: n/a -
Zigbee Boards
XBEE Module Zigbee (S1/S2)
XBEE Module Features & Specifications:
- Indoor Range up to 100 ft. (30 m) & Outdoor RF line-of-sight Range up to 300 ft. (100 m)
- Interface: Serial(UART) at 1200-115200 bps
- Supply Voltage: 2.8 – 3.4 V
- Transmit Current (typical) 45mA (@ 3.3 V)
- Idle / Receive Current (typical) 50mA (@ 3.3 V)
- Operating Frequency: ISM 2.4 GHz
- Antenna: Whip antenna
- Supported Network Topologies: Point-to-point, Point-to-multipoint & Peer-to-peer
- Number of Channels: (software selectable) 16 Direct Sequence Channels
- Addressing Options: PAN ID, Channel and Addresses
- ADC and I/O line support
- AT and API Command Modes for configuring module parameters
- Extensive command set
- Small form factor
SKU: n/a - Indoor Range up to 100 ft. (30 m) & Outdoor RF line-of-sight Range up to 300 ft. (100 m)
-
Modules and Motors, Arduino
ZMPT101B 250V AC Voltage Sensor Module For Arduino
Specifications:
- Measure within 250V AC
- Onboard micro-precision voltage transformer
- Analog output corresponding quantity can be adjusted.
- Good consistency, for voltage and power measurement
- Very efficient and accuracy
SKU: n/a
There are no reviews yet.